色空间对HDRI亮度测量方法的影响

相机内置预处理环节中的白平衡、色度空间转换是数码成像过程中的重要环节,sRGB和Adobe RGB是数码相机2种常用的色空间.为进一步研究色空间对HDRI亮度测量方法的影响,在荧光灯照明的实验室,分别利用sRGB和Adobe RGB色空间对色板成像,测量该亮度测量方法中各色板的标定因数,计算各色板标定因数的相对不确定度.实验结果表明:2种不同色空间获得的标定因数不同,且Adobe RGB色空间标定因数相对不确定度的平均值小于sRGB色空间的;色空间改变后,标定因数需要重新进行标定,且优先选用色域较宽的Adobe RGB色空间.     

二维超声速空气引射器启动特性试验研究

xxxx超声速引射器是高空模拟试车台的重要组件,在发动机启动前利用引射器对试验舱预抽真空可避免发动机启动初始时刻燃气漏入试验舱造成燃气在发动机中分离,对获取发动机在高空环境下的完整推力特性具有重要意义。而该工况下超声速引射器的启动过程是引射器工作过程中最为恶劣的工况,设计不合理的引射器会导致启动压力过高甚至不能实现启动。建立了缩比超声速空气引射器试验台对超声速引射器的启动特性进行研究,采用压力测量方法结合纹影技术对超声速引射器处于极限启动压比时的流场进行了描述,研究结果表明混合室收缩比越小,引射器极限启动压比越低。同时给出了定位超声速引射器不启动原因的判据：当引射器不启动是由引射总压不足引起时,盲腔压力在引射总压提高时降低,并在临界启动状态下达到最小值;而由混合室收缩比过小导致的引射器不启动在引射总压提高时盲腔压力单调上升。     

基于HLA的防区外空面导弹攻防对抗仿真

针对HLA/RTI在接口规范、对象模型模板等关键技术建立分布式仿真平台的复杂性,提出了利用数字武器开发平台进行开发的方法,构建防区外空面导弹攻防对抗系统体系结构,实现了该体系结构联邦成员划分、设计联邦/仿真对象模型表等HLA仿真关键技术,并采用面向对象建模与仿真技术建立了各联邦成员的数学模型.该仿真结果表明,各联邦成员的数学模型与底层支撑环境能够相互分离,仿真模型具有良好的交互性和互操作性,可通过添加或删除联邦成员仿真不同的复杂战场想定,并可作为验证不同算例的仿真平台.     

形象记忆在数学学习中的应用

根据高中数学知识特点及学习方法,在数学概念、公式、定理等的教学中利用形象记忆,有助于学生正确理解基本概念,掌握公式和定理,并且可以培养学生的学习兴趣,提高数学学习的能力。在数学教学中利用形象记忆,也要注意使用方法和范围。     

Thermal hazard assessment of TKX-50-based melt-cast explosive

In the present study, thermal hazards of TNT and DNAN used as the molten binder in TKX-50-based melt-cast explosives were comparatively studied through accelerating rate calorimeter (ARC) and Cook-off experiments. Two kinds of ARC operation modes were performed to investigate the thermal safety performance under adiabatic conditions (HWS mode) and constant heating (CHR mode). The obtained results demonstrated that at both heating modes, DNAN/TKX-50 outperformed TNT/TKX-50 from the thermal safety point of view. However, the sensitivity to heat of the samples was reverse because of the different heating modes. In addition, the results of thermal hazard assessment obtained from the cook-off experiment complied with ARC analysis which indicated the molten binder TNT replaced by DNAN would reduce the hazard of the TKX-50 melt cast explosive. Furthermore, the results of cook-off experiments also showed that DNAN/TKX-50 outperformed TNT/TKX-50 from the aspect of thermal stability, which was consistent with the result of CHR mode because of the similar heating process.     

Formation of adiabatic shearing band for high-strength Ti-5553 alloy: A dramatic thermoplastic microstructural evolution

By using split Hopkinson pressure bar, optical microscopy and electronic microscopy, we investigate the influence of initial microstructures on the adiabatic shear behavior of high-strength Ti–5Al–5V–5Mo–3Cr (Ti-5553) alloy with lamellar microstructure and bimodal microstructure. Lamellar alloy tends to form adiabatic shearing band (ASB) at low compression strain, while bimodal alloy is considerably ASB-resistant. Comparing with the initial microstructure of Ti-5553 alloy, we find that the microstructure of the ASB changes dramatically. Adiabatic shear of lamellar Ti-5553 alloy not only results in the formation of recrystallized β nano-grains within the ASB, but also leads to the chemical redistribution of the alloying elements such as Al, V, Cr and Mo. As a result, the alloying elements distribute evenly in the ASB. In contrast, the dramatic adiabatic shear of bimodal alloy might give rise to the complete lamination of the globular primary α grain and the equiaxial prior β grain, which is accompanied by the dynamic recrystallization of α lamellae and β lamellae. As a result, ASB of bimodal alloy is composed of α/β nano-multilayers. Chemical redistribution does not occur in ASB of bimodal alloy. Bimodal Ti-5553 alloy should be a promising candidate for high performance armors with high mass efficiency due to the processes high dynamic flow stress and excellent ASB-resistance.     

高科技武器装备发展推动作战理念的创新

结合美国在近几年的几次局部战争中所使用的高科技的信息化武器装备、远程作战武器和精确打击武器等武器装备,研究分析了高科技武器装备的发展动态,促进产生了一些新的作战理念(战术战法、作战理论),如网络中心战、夺取制信息权、非对称作战和非线性作战,而新的作战理念又推动了高科技武器装备的完善和进一步发展。同时还分析了高科技武器装备目前尚存在的一些不足。     

切向空气气流对激光辐照碳纤维复合材料的影响

实验研究了靶材表面存在和不存在切向空气气流时,975nm连续激光对碳纤维增强树脂基复合材料的辐照效应,发现切向气流的加载有利于激光对碳纤维复合材料的破坏.从理论上对激光辐照下碳纤维复合材料的破坏机理进行了初步分析,基于碳的氧化特性和氧化反应机理,推导了碳纤维的氧化速率方程.采用改进的光滑粒子方法,对激光辐照下复合材料树...     

基于HLA的导弹攻防仿真系统分析与设计

基于HLA建立仿真应用系统是提高作战仿真活动效率的有效途径。分析了导弹攻防仿真系统的组成和特点,在联邦开发与执行过程模型(FEDEP)基础上,结合作者的开发经验,探讨了基于HLA的仿真应用系统开发的一般过程,将其总结为系统分析、联邦设计、FOM/SOM开发、联邦成员实现与联邦集成四个步骤。给出了某地地导弹与宙斯盾防御系统攻防仿真的系统设计实例。